Cambridge IGCSE Physics 0625 Paper 6 is a written Alternative to Practical exam. It lasts 1 hour, carries 40 marks and contributes 20% of the qualification. Paper 6 assesses experimental skills through written tasks. Both Core and Extended candidates take either Paper 5 or Paper 6, depending on their entry. Cambridge 0625 syllabus, practical assessment and experimental skills
What does Physics Paper 6 test?
Expect questions that use apparatus diagrams, measurements and data to ask how an investigation works. You may have to read a scale, complete a table, draw a graph, use evidence to reach a conclusion or plan an investigation. The syllabus lists contexts such as measuring lengths or short intervals, investigating a spring, finding resistance or studying light. Use each context to practise the same underlying skills.
| Task | What to show in your answer |
|---|---|
| Record a measurement | Quantity, unit and precision appropriate to the instrument or instructions |
| Complete a results table | Clear headers with units and values aligned by trial |
| Plot a graph | The requested axes, usable scales, accurately placed points and the specified fit |
| Calculate a gradient | Two coordinates from your fitted line, differences and division |
| Draw a conclusion | A relationship or comparison backed by the data |
| Plan an investigation | What changes, what is measured, what stays fixed, how results will be processed |
Worked example: timing a pendulum
Suppose the question asks you to plan how the length of a pendulum affects its period. State how you will measure length from the point of suspension to the centre of the bob. Choose several lengths, keep the same bob and use the same small release angle each time. Release it without pushing and use a fixed reference position to count complete oscillations consistently.
At a length of 0.40 m, three readings for 10 complete oscillations are 12.6 s, 12.8 s and 12.7 s. Their mean is 12.7 s, so the period is 1.27 s. Use the same procedure at each length. State what you will plot. A graph of period against length addresses how the period changes. If the prompt specifically asks you to test proportionality between period squared and length, calculate period squared for each row and plot that instead.
What makes the plan replicable? “Keep the setup the same” leaves the reader guessing. “Use the same bob and release it from the same small angle” names two controls. “Record time” leaves the number of swings unclear. “Record the time for 10 complete oscillations, repeat twice, then divide the mean by 10” tells the reader exactly how you will obtain one result.
How to plot a graph and find its gradient
Read the axis instruction first. In “plot y against x”, y goes vertically and x horizontally. Choose a consistent scale with sensible intervals and enough space for your data. Label each axis with the quantity and unit, then plot small crosses or points. Follow the instruction for a best-fit line or curve. A line drawn from dot to dot makes individual measurement variation look like a real change in the relationship.
For an original example, suppose a straight best-fit line on a voltage-current graph passes through (0.10 A, 0.50 V) and (0.50 A, 2.50 V). Its gradient is (2.50 − 0.50) ÷ (0.50 − 0.10) = 5.0 V/A. If the graph represents potential difference against current for a fixed resistor at constant temperature, this gradient represents 5.0 Ω. Choose points on your fitted line with a wide separation. They can differ from the plotted readings.
Build a practice paper in PrickyAI
Choose questions for a practice session and work through the paper in the app.
Answer evaluation questions with evidence
When comparing two readings, calculate the difference if it helps you use the criterion in the question. For example, values of 4.1 cm and 4.3 cm differ by 0.2 cm. If the stated tolerance is 0.3 cm, the values agree within that tolerance. Use the tolerance supplied in the question. Some questions ask for a qualitative judgement and expect you to cite the measurements.
When proposing an improvement, link the change to a concrete problem. Timing multiple oscillations makes the measured interval longer, reducing the fractional effect of human reaction time on the period. Reading a ruler with your eye aligned squarely with the scale reduces parallax. Repeating and averaging readings helps reduce random variation. A zero error needs a different response, such as checking the instrument zero and applying a correction where appropriate.
A second planning example: extension of a spring
Measure the spring's unloaded length first. Hang a known load, let the spring settle, and read its new length against a fixed vertical ruler. Subtract the unloaded length to find the extension. With a starting length of 11.0 cm and a loaded length of 14.6 cm, the extension is 3.6 cm. Record force and extension in separate columns. Repeat for several loads using the same spring and measuring from the same reference point.
If asked whether extension is proportional to force, plot extension on the vertical axis against force on the horizontal axis. Look for a straight line through the origin within the range investigated. A straight line that misses the origin may indicate a measurement offset or a failure to subtract the unloaded length. Discuss what the data show before suggesting a reason for the offset. Avoid claiming proportionality over a range you did not measure.
How to practise with Paper 6 past papers
Open Cambridge's 0625 past paper page and match the question paper and mark scheme by year, series and component. If the relevant variant is missing from the public selection, ask your teacher which material your school can share. Do one graph and one planning question before a full timed paper. Print the graph grid at its original scale or use squared paper where appropriate.
After marking, record whether each dropped mark came from a reading, an incomplete method, the graph or an explanation. Redo your weakest task on fresh data. For Paper 4 calculations, see the separate science method marks guide.
One-minute check before handing in
- Check each measured quantity has the requested unit.
- Match graph axes, scales and fitting instructions to the prompt.
- Show the coordinates used for a gradient.
- Name the variable you change, the one you measure and the specific controls.
- Check that your conclusion refers to your evidence.
Practise reading scales and checking repeated measurements
Start by finding the value of the smallest division. A ruler marked every millimetre lets you record a reading such as 6.2 cm to the nearest millimetre. If the ends of a component line up with 2.4 cm and 8.6 cm, the length is 8.6 − 2.4 = 6.2 cm. This subtraction also helps when the ruler has a damaged zero end and you deliberately start from another mark. State the unit and use the precision requested.
Repeated readings help you check consistency. Suppose you record 21.0 s, 21.2 s and 25.4 s for the same task. The third reading is substantially different. Check for a miscount or a recording error, and repeat the measurement if possible. If the question tells you how to treat an anomalous result, follow that instruction and show which values went into your calculation. An anomaly is a reason to investigate the measurement before deciding how to use it.
Worked example: turn a results table into a conclusion
An original spring investigation gives the following readings. The unloaded length is 9.0 cm. The load is applied vertically and the spring is allowed to settle before each reading.
| Load in N | Loaded length in cm | Extension in cm |
|---|---|---|
| 0.5 | 10.0 | 1.0 |
| 1.0 | 11.0 | 2.0 |
| 1.5 | 12.0 | 3.0 |
| 2.0 | 13.1 | 4.1 |
The extension is the loaded length minus 9.0 cm. For the last row, that gives 4.1 cm. Plot load horizontally and extension vertically if asked for a graph of extension against load. Use the fitted line to choose a gradient triangle with points far apart. For a line passing through (0.5 N, 1.0 cm) and (2.0 N, 4.0 cm), the gradient is (4.0 − 1.0) ÷ (2.0 − 0.5) = 2.0 cm/N. The second point is read from the line, so it can differ from the measured 4.1 cm.
A conclusion can state that the data are consistent with approximate proportionality over the loads measured. When the load doubles from 1.0 N to 2.0 N, the extension goes from 2.0 cm to 4.1 cm, approximately double. Check both the shape and the intercept of the fitted graph if the question asks you to assess proportionality. Cambridge's report comments on how candidates showed their gradient calculations. Cambridge 0625 June 2024 examiner report
Use PrickyAI alongside a handwritten practical paper
In PrickyAI, choose Physics and use short sets to revisit the underlying topics, such as circuits or forces. Draw each table or graph on paper. When you review a past-paper task, keep the matching scheme open so you can check the axis labels, units, choice of coordinates and the conclusion separately.
After the first attempt, choose one skill for a fresh question. For a gradient mistake, use a new set of axes and write the change in each quantity before dividing. For an incomplete plan, have a partner read your instructions and point to any quantity they would have to guess. Once those checks are consistent, sit a full 60-minute paper using your centre's guidance on equipment.



